Manuscript template for the journal

Surname A.,1 Surname B.,2 and Surname C.2,3

1 University, Department, Address, Country, e-mail of the corresponding author

2 Institute, Laboratory, Address, Country

3 Optical elements Ltd., Address, Country

Received: dd.mm.yyyy

Abstract. Each manuscript requires a leading abstract (less than 100–150 words) in English summarising significant coverage and findings. If the work of another author is cited in the abstract, that citation should be written out without a number, (e.g., journal, volume, first page, and year in brackets [Ukr.J.Phys.Opt., 22: 1234 (2014)]), and a separate citation should be included in the body of the text.

Keywords: Three to six keywords are required, which characterise the contents of the article.

UDC:

Introduction

Please note the references should appear at the end of the article after the Funding and Acknowledgments sections. The first reference cited in the main text must be [1].

Page layout and length

The text should be typed, using Times New Roman font (10-point size, 1.2-line spacing). Margins: Top – 3.0, bottom – 4.7, left – 3.5 and right – 3.5 cm, paper size – А4.

Typographical style

3.1. Title

Use the initial cap for the first word in the title or for proper nouns.

3.1.1. Author names. Author names should appear as used for conventional publication, with surname followed by initials or first and middle names. Every effort should be made to keep author names consistent from one paper to the next as they appear within our publications.

3.1.2. Author affiliations. If all authors share one affiliation, superscript numbers are not needed. For different affiliations, all authors must have superscripts to call out each affiliation. Hard returns (Enter key) must be used to separate each individual affiliation. Abbreviations should not be used. Please include the country at the end of the affiliation.

Main text

Section headings may be numbered consecutively and consistently throughout the paper in Arabic numbers and typed in bold. Use an initial capital letter followed by lowercase, except for proper names, abbreviations, etc. Do not include references to the literature, illustrations, or tables in headings. Subsection headings may be numbered consecutively in Arabic numbers and typed in italic bold. Sub-subsection headings may be numbered consecutively in Arabic numbers and typed in italic. The text of the sub-subsection should follow the title.

Equations, figures, supplementary materials, and tables

5.1. Equations

All display equations should be created in MathType. Inline equations can be created with this tool or by using a keyboard and Unicode characters where needed for the best quality line spacing. We strongly encourage authors to use MathType 6.9.

(1)

The equations should be numbered with consecutive Arabic numbers. The configuration file for the MathType 6.9 can be downloaded (Formula.Preferences.UJPO.eqp).

5.2. Figures

Figures may be inserted immediately into the text. All of them should be numbered with consecutive Arabic numbers, have descriptive captions and be referred to in the text as e.g. Fig. 1. Captions should be set immediately below the figures. Figures should be prepared in a readable computer form, with the resolution not less than 450 dpi for grayscale or black/white figures (JPEG or PS formats). Colour figures should be prepared only in TIFF or JPEG format (not less than 300 dpi). The figure width should not exceed 14 cm. The line thickness must be chosen on this basis and all the lettering, and symbols should correspond to the text font size. Figures should never be placed in a table environment, embedded inside the text, or included within a list. All the figures should be centered. No part of a figure should go beyond the typing area. Place figures as closely as possible to where they are mentioned in the text. Figures should be numbered consecutively in the order of appearance and citation in the text. Be sure to cite every figure.

Fig. 1. Figure caption.

5.3. Tables

Insert tables into the text or gather them at the end of the article. Number tables consecutively with Arabic numbers and give each a clear descriptive caption at the top.

Table 1. Elastic stiffness and compliance coefficients known for the Pb5Ge3O11 crystals.

, 10–12 m2/N	S11	S12	S13	S33	S14	S25	S44	S66
Ref. [26]	17.7	–6.4	–2.2	11.4	0	–1.3	44.5	48.3
, 109 N/m2	C11	C12	C13	C33	C14	C25	C44	C66
Ref. [26]	68.4	26.8	17.9	94.3	0	1.2	22.6	20.8
Ref. [27]	68	25.7	18.9	94.2	0	0.8	22.3	21.1

5.3.1. Supplementary materials. Supplementary materials (up to 10 MB), such as visualizations, Data Files, etc. can be uploaded after agreement with Editorial Group.

Funding. Authors may add the details about a funder that are required, or they may be added to the Acknowledgments. At the submissions, please include funder names and grant numbers in the manuscript.

Acknowledgments. Acknowledgments should be included at the end of the document. Additional information crediting individuals who contributed to the work being reported.

Disclosures. Disclosures should be listed in a separate section “Disclosures” at the end of the manuscript. If there are no disclosures, then list “The authors declare no conflicts of interest.”

References

References should appear at the end of the article after the Funding and Acknowledgements sections as:

References

Azzam R M A and Bashara N M. Ellipsometry and polarized light. Amsterdam, New York: North-Holland, (1977).

Mys O, Kostyrko M, Adamenko D, Skab I and Vlokh R, 2022. Acoustic polarization singularities arising under torsion and orbital angular momentum exchange at the backward collinear acousto-optic diffraction: a case of crystals with point symmetry 3m. Ukr.J.Phys.Opt. 23(2): 107 – 115.